Full automatic monoblock filling unit with RINSER, FILLER and ROPP CAPPER:
the rinser is used when filling new glass bottle to remove particles such as dust, condensation water, small insects, etc. The utilization of a rinser gives the bottling plant additional product safety.
With the appropriate options it is also possible to achieve an internal sterilization with a bacteria killing liquid.
The bottle is gripped securely by the gripper at the bottleneck and then quickly turned upside down by the twist system. The treatment agent (sterile water, ozonized water, air, inert gas, aqueous cleaning solution, etc.) is then injected into the bottle via a nozzle. After an appropriate dripping time, the bottle is moved back on the conveyor. "No bottle no spray system". If there is no bottle in the gripper the nozzle is not spaying.
Optionally it is possible to install a two-step rinser system. For example, cleaning fluid and then blow out with air or inert gas.
The cleaning liquid can optionally run through a recycling system. The cleaning solution is collected and pumped through a micro filter and then used again in recirculating.
The 1000 times proven filling valves of the E2 series can work with gravity (drop pressure) as well as under negative pressure (light vacuum).
Filling under slight negative pressure (optional) on the one hand causes a better release of the filling and on the other hand it is helpful with slightly foaming products and prevents dripping on the filling valve with worn-out seals.
The height of the bottle is adjusted by handwheel (manual) or can also be done electrical (optionally).
The filling height is set by means of appropriate spacers which are used in the filling valves.
Pneumatic lifting of the bottle plate and mechanical lowering via cam (no air consumption).
The tub has a central liquid inlet and is mirror polished inside. Total discharge drain with ball valve installed on the bottom of the tank. The opening of the filling valves for sterilization (for example with steam) or for cleaning takes is achieved by stainless steel clips.
Filling valves are easy to remove and can be completely disassembled easily.
Optionally available are two models of cleaning adapters which are used for final cleaning. A cleaning water collection trough installed under the filling valves or in alternative a cleaning rim with dummy bottles which allows to collect the cleaning solution under the valves and wash the valves also in countercurrent (backwash).
The liquid feed into the filler tank is controlled via sensors. The sensors will command the pneumatically operated product supply valve and a pump control.
Other options: hot-filling equipment, high-vacuum or light-pressure filling. Device for foam extraction.
Corker for natural, agglomerated, and synthetic corks for wine bottles.
Construction of stainless steel with stainless steel head, bronze chariots, and jaws of hardened and ground N690 steel.
Simple adjustment of the closure of the jaws on an eccentric pivot. Big capacity hopper with new-design mechanical cork selection disc.
Cork plunger mounted on self-lubricating bushes and rods of chrome-plated steel ground for absolute absence of clearance even due to wear.
As an option is available the innovative vacuum closure does not use any vacuum pumps but a yet of compressed air exploiting the principles of Venturi tube.
The frame of the monobloc is made of stainless steel. All doors are equipped with safety devices in the hinge. The control of the monobloc is carried out via a central control cabinet made of stainless steel. The system is easy and clear to use and also the format change can be accomplished quickly.
Thanks to the modular design and the wide range of additional options, the machine can be optimally adapted to the needs of the company.
The system is prepared to be integrated into a filling line; without belt, belt drive and bottle collection table.
Belt, belt drive and bottle collection table are available as options. In addition, larger bottle feeding tables are available Ø600-800-1000 mm and bottle collecting tables Ø600-800-1000 mm with belt drive at the end of the line. Belt connections between different machines are available on request.
Filling Monoblock in linear design with single-head corker for straight cork
Rinser: 12 grippers max. 2500 b/h
Filler: 12 valves max. 2200 b/h
Capper: single head corker with fully automatic cork distribution max. 2000b/h.